Search results for query: *

Thanks I'm going to try and get to working on it, but it's been raining pretty much every day, so I can't really use it anyway. But I'm trying to get it fixed so when it's finally dry I can use it

Can anyone tell me how to time a vicon Fanex 500 Tedder? It is a 4 basket Tedder and the tunes are clanking together. I checked YouTube and couldn’t find the answer.

We put on a new pump a few years back we accidentally put on wrong year pump did not find out putting fan on so just bought fan to match the pump every thing work out fine

Sorry for the long break. I did manage to get the individual rollers out. It had caps on each side, kind of like bottle caps but bigger, I had no idea until I had spoken to someone about it, and it had to be in the forward position to locate and remove them. They were difficult to remove...

Thanks Mat I am attempting to change all the drive and idlers sprockets, does roller assembly come out the front or rear of baler ? May talk new Holland tomorrow.

Does any one know how to take out sledge assembly 6 series New Holland baler it has some kind of end caps on out sides of bailer and I for world cant figure how to remove them ?? I am attempting to take out all the rollers and change idlers drive sprockets. My baler. is 650

I measured and my old belts and they are 3 in. shorter than factory because they have been trimmed in the past. So, we spliced it and ran it again, it worked well for one day, made 15-18 bales, and then broke again. I am going to get it remade tomorrow with a longer splice, I think it was too short.

Greetings fellow posters, Does it ever make since to change just one belt if it is the only one actually broken, but all of them are old and could use to be replaced. This machine has needed a lot of repair this year and I was hoping to wait until next year to change all of the belts. Does this...

:cboy: :D :cboy: :D :cboy: :D It is fixed! It had a small hole in a suction line caused by a limb. I found the hole by blowing air into the reservoir with the compressor. The pump had lost its prime , replaced line re-primed pump works great

magnet look good.My hyd pump runs off the injector pump took line off hyd pump no oil inside added oil ran motor pump shaft turns inside of pump but no pressure . Took other lines off no pressure there either. going to take off line and try a little air pressure to see if I can get fluid moving

Thanks Kenny, but it is a total failure not steering, hydrostat transmission, or anything. BTW it is a L4850.

Hello, I let someone borrow my tractor and so I do not know the events that led to this but my Kubota has completely lost use of the hydraulic systems. No bucket, transmission, steering, and no rear lift. I think there was some contaminated hydraulic fluid that was put into the system. I have...

Our tractor has been shop again the shaft in pump broke after about 2hrs of cuting hay, suppose to get it back soon . The problem i have is the new pump is coming same manufacture and same lot as the one that just failed it is new holand /ford import part.

Has anyone ever added line off the tilt of frontend loader ? I gave it a try as my tractor has no remotes ,it will raise the bailer door but will not close well only a little at a time and wil not lock down. :cry2: I tried with front cly hooked up and capped no better either way.

I have been awful busy lately did finish bailing what i had cut.The pto.did stay in gear all the time unless I lowerd the rpms once to go out a gate an went out of gear with leaver still engaged could not get to reengage until got bail out an restarted fine when empty .We will get a new pump...

Our ford 6610 runs well with no load or an empty hay-baler. However, if I turn off the P.T.O. to turn around at the end of row with a partial bale in the baler, I cannot get the P.T.O. to start turning again. If I release the hay-bale, it will start turning again. On ocasion, I will be able to...

I bought my bailer a couple years ago, used. Now the drive sprocket on the end of rollers on the inside of bailer have a good bit of wear on them. Does anyone have any experence changing them? I have small excavator to pull out roller assembly, thanks. I have good friend who much better...

Put it in the cut position was able to free it up. Checked the oil and ran it a little while. Doesn't cut well because most of the blades are gone. Makes an intermittent clanking sound. Just want to know if the holes are a big deal or not before I make other repairs. By the way when you turn...

I got this new to me mower, on the top of the drums on top of the drum there is a cover like a 5 gallon paint can lid cover, that is rusted through with holes the size of a dime. Is this bad?? Also, It may be frozen the shaft doesn't want to turn by hand, but it is in the travel position and i...

Our hay cutter bar is rusted, pited, and leaks oil out of three small holes. I j/b welded the holes and painted over. After cutting all the paint and most all the j/b weld wore off . I was thinking of using the paint stuff for for truck beds it should be more durable. Anyone know of anything...