Non emmison sthil carb?

Help Support CattleToday:

Nesikep

Well-known member
Joined
Dec 13, 2008
Messages
16,674
Reaction score
1,181
Location
Lillooet, BC, Canada
not sure, but there's a possiblity that a 044 carb would fit.. can probably be found on Ebay.

There are a number of chainsaw groups on Facebook if you're on there, as well as Arboristsite.com and a bunch of others.. outdoorpowerequipment, sawhogs, etc
 

jltrent

Well-known member
Joined
Aug 25, 2013
Messages
5,360
Reaction score
1,339
Location
Virginia
They usually come with a Walboro and the AM's are Zama or no name stamped on them. Buying the AM are hit and miss, but I have had pretty good luck with them. MS 440 and 044 have the same carb as I have both saws, but the MS441 is an EPA carb. I would try a carb kit first as they are easy to put in just have to be careful with the little tricky spring. Usually the problem is a deformed carb needle tip from ethanol gas or a stiff diaphragm. Also what is the chainsaw doing as it may not be the carburetor? NE Tennessee what town are you close to?

Here is a manual for it....also page 48 is some good info.........

https://www.stihlusa.com/webcontent/cms ... manual.pdf

Here is a carb kit in the US that will ship fast........

https://www.ebay.com/itm/K10-HD-Carbure ... m570.l1313

Here is an AM carb that can be hit or miss.......

https://www.ebay.com/itm/Carb-Carbureto ... itleDesc=0
 
OP
H

hillbilly beef man

Well-known member
Joined
Sep 23, 2006
Messages
1,462
Reaction score
35
Location
northeast TN
The saw is cutting off after about half an hour of sawing. About 4 pulls starts it back and it will run for another half an hour. I am about an hour east of Johnson City.
 

Atimm693

Well-known member
Joined
Oct 14, 2016
Messages
932
Reaction score
253
440 should not have an EPA carb, will likely have limiter caps but those are easily defeated with side cutters.

I would check the tank vent as well.
 

jltrent

Well-known member
Joined
Aug 25, 2013
Messages
5,360
Reaction score
1,339
Location
Virginia
hillbilly beef man":32kal87s said:
The saw is cutting off after about half an hour of sawing. About 4 pulls starts it back and it will run for another half an hour. I am about an hour east of Johnson City.
If the saw is running right and cutting off after getting hot might be a coil issue, but usually they want start back until cool. Also as stated tank vent or intank fuel line bad, intank filter plugged, they could run right and then go south after a few minutes. A pressure/vacuum of the tank can check the vent and line quick, could be incarb screen about plugged You must be close Shady Valley/Mountain City area.
 

True Grit Farms

Well-known member
Joined
Jan 4, 2016
Messages
9,453
Reaction score
4
Location
Middle Georgia
jltrent":npz1b9n3 said:
hillbilly beef man":npz1b9n3 said:
The saw is cutting off after about half an hour of sawing. About 4 pulls starts it back and it will run for another half an hour. I am about an hour east of Johnson City.
If the saw is running right and cutting off after getting hot might be a coil issue, but usually they want start back until cool. Also as stated tank vent or intank fuel line bad, intank filter plugged, they could run right and then go south after a few minutes. A pressure/vacuum of the tank can check the vent and line quick, could be incarb screen about plugged You must be close Shady Valley/Mountain City area.
Highway 421 into and out of Shady Valley is a must ride if you like mountains.
 

jltrent

Well-known member
Joined
Aug 25, 2013
Messages
5,360
Reaction score
1,339
Location
Virginia
True Grit Farms":1oinw49f said:
jltrent":1oinw49f said:
hillbilly beef man":1oinw49f said:
The saw is cutting off after about half an hour of sawing. About 4 pulls starts it back and it will run for another half an hour. I am about an hour east of Johnson City.
If the saw is running right and cutting off after getting hot might be a coil issue, but usually they want start back until cool. Also as stated tank vent or intank fuel line bad, intank filter plugged, they could run right and then go south after a few minutes. A pressure/vacuum of the tank can check the vent and line quick, could be incarb screen about plugged You must be close Shady Valley/Mountain City area.
Highway 421 into and out of Shady Valley is a must ride if you like mountains.
After going over that mountain up by Bristol Nascar Race Track (the way I go) that valley opens up and is one of the prettiest places I have been.

Remember these curves TGF? I live on mountain curves and this has me on my toes driving.
7024382.jpg


Here is a picture, but it doesn't do it justice as far as beauty though....As soon as you come out of the mountain this is what you see and a Zetor tractor dealer on the right...
bd79c7ca-a0d5-4e03-b6e8-a548248134de.c10.jpg


5382147999_a1508c9fec_b.jpg


Sept3-Shady-valley.jpg


Snake-Burger.jpg
 

Latest posts

Top